The aim of the thesis is to analyse and understand resolution, repeatability and reproducibility of the Measurement system for package distance. The Measurement system for package distance is already in use, no Gage R&R has been performed on the system and before spreading use of the system the quality of the system has to be understood and approved.

Flow measurement is one of the greatest challenges in order to calculate efficiency in hydropower. Most hydropower plants in Sweden use differential pressure methods for flow measurement. These methods are dependent on constant conditions in the waterways. A change in these conditions, like turbine improvements, prevents differential pressure methods to verify efficiency improvements. Since efficiency improvements can?t be verified by one Measurement system, another method, which isn?t affected by changing conditions, can be used.

A system for sampling of alcohol and aldehyde from diluted exhaust gases from vehicles powered by ethanol has been developed and tested. The major part of the work has been research of earlier work in the field and the construction of the sampling system.The part of the system constructed for the measurement of alcohol has been shown to work, however, more test should be performed. The part of the system constructed for the measurement of aldehyde was tested parallel to a commercially available system, based on the same principle of measurement, and has been shown to work well.Determination of the concentration of gaseous ethanol using a FID has shown the since earlier known fact that a FID is not able to measure a correct concentration of ethanol. Furthermore it has been shown that high concentrations of gaseous ethanol can not be kept in a bag more than a few minutes without a substantial decrease of the measured concentration..

This thesis describes a method of measuring axial magnetic leakage flux in an operational hydropower generator. Axial magnetic leakage flux is the magnetic flux at the ends of a rotating generator, which goes through the stator parallel to the rotor axis. This flux can cause circulating currents in the stator iron, giving rise to losses, and can in the worst case overheat a generator, causing it to melt down. To measure the axial flux, and how it affects the generator temperature, a Measurement system was constructed on behalf of Vattenfall. The system consists of search coil sensors and a signal-processing unit with amplifiers and active filtering.  To confirm the behaviour of the axial leakage flux and the functionality of the Measurement system, a test installation was made.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

A performance Measurement system can be used as a means to evaluate past performances and to communicate prioritizations. It has also been proposed that a performance Measurement system can serve as a method to execute strategies, guide in operational decisions and constitute a tool for making the organization more efficient. Yet one may question if such a system will ever reach this capacity if operating managers do not utilize it as a management tool, but rather treat it as a mere report in the bunch. This paper explores how middle managers in fact apply performance measures and what obstacles there are to integrating them in the management of subunits. Furthermore it serves to investigate whether these managers experience a conflict between how they are expected to use the measures and what they deem possible to adopt.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

The purpose of this thesis is to identify the factors that drive efficiency and effectiveness in technical development projects performed at A?F?s department of product development. In addition to identifying and analyzing these factors, the thesis also analyzes what needs to be taken in to account in order to implement a Measurement system that is able to both monitor and control the identified factors.The thesis has been performed in a qualitative manner. It is based on interviews with people from several different technological companies, within different lines of business, all of which are customers to A?F?s department of product development.The results show that there are seven critical factors for project efficiency and effectiveness.

Storing kinetic energy in a flywheel allows for more efficient driving of electricvehicles. Research in this area is in progress at Uppsala University, where a flywheelwith magnetic bearings encased in a vacuum chamber is being constructed. To makethis possible methods for measuring the current through the electromagnets in thebearings and temperatures in the flywheel need to be developed. This has been thepurpose of this report. The current measurement resulted in a resistive method, andthe implementation of eight measurement circuits in the system.